IKHbike

Thanks very much,am going to change all three. I have downloaded a manual but cant find what you have shown, particularly the picture of all three separate belts !

Cant find any pictures of the three separate belts(Alt/Power's/Ac) and the relevant adjuster bolts .All pictures I find are one big belt for the IS200 but when I bring up belt to order they are three separate,can anyone advise ? Thanks all!

ICO is the code under the bonnet(nothing in the door other than tire pressure and air bag information) but the car has a definite green pearl half the time.I'm just not convinced,someone tell me that this is or isn't just silver metallic please!

Same issue since buying mine,finally have an opportunity to look at it,will there ever be an answer to the frozen passenger?

Anyone have a list of the colours and the use for each of the wiring harness bundles?, as in I have two that have been cut into one Brown with green tracer (big bundle of about 10 leads) and one smaller white with green tracer with 3 leads coming from it, If I new what the particular bundles of wires did I'd be on a roll.When I finally solve this brake warning light issue out I will put something up with suggestions to avoid some of the time we have wasted going down blind alleys! Thanks all,and thanks for all help since joining!!

Where do I post them for instance in 1st gen IS200 forum please?

Seems if we pull stork back to flash head light it works,also when relay removed last night the day day driving lights came on but not headlight. opened the headlight relay and its fine.So power to lights and bulbs work and relay intact,and before number plate bulb replaced all fine.Not sure where electrical issue part of forum is so sorry if in wrong section.

Replaced left hand number plate bulb and for 30 sec brake light on dash off and everything working then headlights go off,headlight wash not working either .There is a separate ecu for both R and L H'light and one to wash motor behind f'bumper.Headlight fusses good but main relay in under bonnet fuse box not appearing to click(When lights switched on power to two of four pins in fuse box) I might add that both front f'fog lamps are disconnected and wires cut,both rear fog lamps are fine(but not operative) I have no idea how long bulb to number plate blown as have been tracing a TRC and brake light issue(TRC working) ,why would the bulb being replaced affect the relay if that is it.Thanks for any ideas

Replaced the ABS sensor and abs light no longer a problem(sensor showed correct resistance but obviously something still wrong) but brake light still on.Traced to a blown number plate light ,replaced this and all was well for 30 sec then lost headlights!!.tail,brake number plate all working and all indicators working.No fog lamps front are disconnected(one rotten both have had connection cut of),rear ones are fine.All fusses under bonnet ok but big solenoid does not appear to click,lights where fine prior to replacing a number plate bulb. GIBBER!!

TRC flashing,comes on after about 500 yards then stays on and both come on each time ignition on,blast you can tell what stage of frustrated I am that I was willing to go with even fog lamps.There is a solenoid missing dimmer switch or light,its the bloke of solenoids just above the diagnostics plug!

Is there a Toyota version of BMW NCS expert?

Is there a Toyota version of BMW NCS expert?

...spoiler lamps,you mean fog lamps.Connection to these is missing and both bulbs are a mess,no visible cable though I did look on line to find that it should be a white with black trace and a red lead,possibly a green also?

TRC button does nothing(checked button/switch and it works) as for pad wear sensors I have come across nothing in the manual to suggest an electrical form of sensor, have I missed something. Thanks for reply by the way

YES?

Given up,have dredged the internet for answers and none solve it. MOT has run out,my holiday has run out and my patience has,replacing all four tyres(front look great until you put it on full lock!)prospect of taking it to a Lexus garage to run tests to find exact fault and replacing part's before sorting tracking and getting MOT is frankly more than the car is worth.It drinks fuel like a four litre car(three country road trips of about seven mile recorded 13mpg!) on average less than 20mpg. Its a solid car and no one could say its mechanical condition gives away its 170 thousand miles but the electrics are a nightmare! Anyone got a Fiesta going cheap?

Have had it checked by two diagnostic computers today.Found nothing on first one at my local MOT station and finding the fault or at least part of it being the front passenger ABS sensor at one of our local auto tech colleges (thanks to my daughter asking her boyfriend,cheers Thami!) am looking to the Lexus IS200 ABS Pump + Module 44540-53020 133800-5500 as have checked continuity on all four sensors and all good.Will clean sensor first and toothed wheel etc. Have noticed an odd vibration in the steering at about 60 mph on some sections of dual carriageway that makes me think the pump may be faulty?

I know this is an old conversation,I've just been looking for my own use and according to the repair manual you can adjust toe and camber in graduated degrees on front and rear!.

Hi all,first try in the snow in Lexus. Well it has been sleeting on and off all day (12/1/17),attempted to drive up hill from my home earlier and got about 200 yards before wheel spin took over.reversing then trying again made no difference(snow mode or not) so reversed turned and parked facing down exactly same place started. Have driven all sorts in the snow and had no problem,including rear wheel drive delivery trucks but the IS 200 just said nope,go home,now!

TRC light flashing and handbrake light on permanent .Have repaired a damaged ABS cable on the front passenger side and tested the resistance before replacing.Did the wire cross in the diagnostic box and lights go out,press brake the H'brake light returns then half a mile later TRC light on. Replaced rear pads,checked front pads and checked ABS sensor on driver side and rear left and right. Start car lights out then same as before. Have looked at handbrake shoes and all seems fine.The (i) light went out when I released the handbrake after ecu cleared but as soon as pedal pressed it came on and stayed on until ecu cleared again.Any ideas as have no hair to pull out!

Have same problem,TRC light flashing and handbrake light on permanent .Have repaired a damaged ABS cable on the front passenger side and tested the resistance before replacing.Did the wire cross in the diagnostic box and lights go out,press brake the H'brake light returns then half a mile later TRC light on. Replaced rear pads,checked front pads and checked ABS sensor on driver side. Start car lights out then same as before,except now I need to bleed the brakes!Any advice very thankfully recieved

Posted January 8, 2013 I have a very similar problem on mine. The Windscreen washer works fine and i can hear the motor when i press the switch for the headlights but other than that, nothing. I've tried all the tips in this thread, (barring the new motor). Same issue only my washers don't come out and screen wash filler tube is split I think as it only holds a little water. Can hear motor nothing else!? Any ideas?? pleeease