Do Not Sell My Personal Information Jump to content


Do I Have Any Volenteers ?


Chris.S
 Share

Recommended Posts


I haven't got access to a trailer and the cars stuck on the ramp at work.

I want to remove the charger so the guys at work can just do the engine swap, should make the job faster

Link to comment
Share on other sites

remove air filter box and scoop

loosen belt tensioner

remove belt

loosen silicone pipework

undo 4 bolts at top

undo throttle linkage

lift out s/charger

cradle 3no. bolts

throttle inlet loosen silicone pipework and slide down pipe

easy peasy !

Link to comment
Share on other sites

remove air filter box and scoop

loosen belt tensioner

remove belt

loosen silicone pipework

undo 4 bolts at top

undo throttle linkage

lift out s/charger

cradle 3no. bolts

throttle inlet loosen silicone pipework and slide down pipe

easy peasy !

HMMMMMMMMMMMMMMMMMM, didnt i tell you that on wednesday :)

Link to comment
Share on other sites

remove air filter box and scoop

loosen belt tensioner

remove belt

loosen silicone pipework

undo 4 bolts at top

undo throttle linkage

lift out s/charger

cradle 3no. bolts

throttle inlet loosen silicone pipework and slide down pipe

easy peasy !

HMMMMMMMMMMMMMMMMMM, didnt i tell you that on wednesday :)

:lol::lol:

:blush:

guess what it worked !

now can i have the put it all back together instructions :D

Link to comment
Share on other sites

remove air filter box and scoop

loosen belt tensioner

remove belt

loosen silicone pipework

undo 4 bolts at top

undo throttle linkage

lift out s/charger

cradle 3no. bolts

throttle inlet loosen silicone pipework and slide down pipe

easy peasy !

HMMMMMMMMMMMMMMMMMM, didnt i tell you that on wednesday :)

:lol::lol:

:blush:

guess what it worked !

now can i have the put it all back together instructions :D

easy peasy !

slide silicone pipework down the pipe and tighten the clamp to the throttle inlet

fit cradel

lift in s/charger

do up 4 bolts at top

tighten throttle linkage

re-fit silicone pipework

re-fit belt

tighten belt tensioner

replace air filter box and scoop

Link to comment
Share on other sites


remove air filter box and scoop

loosen belt tensioner

remove belt

loosen silicone pipework

undo 4 bolts at top

undo throttle linkage

lift out s/charger

cradle 3no. bolts

throttle inlet loosen silicone pipework and slide down pipe

easy peasy !

HMMMMMMMMMMMMMMMMMM, didnt i tell you that on wednesday :)

:lol::lol:

:blush:

guess what it worked !

now can i have the put it all back together instructions :D

easy peasy !

slide silicone pipework down the pipe and tighten the clamp to the throttle inlet

fit cradel

lift in s/charger

do up 4 bolts at top

tighten throttle linkage

re-fit silicone pipework

re-fit belt

tighten belt tensioner

replace air filter box and scoop

damn....... i knew i should have kept them bolts :D

Link to comment
Share on other sites

Can pop down later if you like Chris but haven't got a clue what I'm doing?

Just waiting to find out if I'm at work or not at the minute though so that could stop me mate.

Link to comment
Share on other sites

Sort of mate, hopefully my sat nav should be back up and running at some point today if I can get the receiver to do a full reset!

I'll see if I can find out what's going off today, we're waiting on someone to release some software and it's not there yet :(

Link to comment
Share on other sites

If the engine is being LIFTED out Chris, you'll have to probally detach all the intercooler pipe work, but sure you can leave the bendy bit at the intake on mate, unless theres bolts underit where they have to seperate the top from the bottom of the engine.

Not hard to remove that piece, just an allen key mate, and a good wiggle afterwards and pull in an upright movement ..

Link to comment
Share on other sites

If being DROPPED out Chris, still need to unde the Intercooler pipework so it will DROP out..

I think MAt C will be the best person to ask thereafter, as I have never taken an engine out before, only fitted and removed SC kit. Can help you fit it back at JAE.. Bring some tools etc if you like .

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share



×
×
  • Create New...