Harpreet

Hello all The exhaust backbox on my IS250 has come off the body and exhaust pipe (Y-section). It is due to corrosion between the pipe and backbox junction. I cannot afford just now to put a new y-section on, so trying to repair it by inserting an expanded pipe sleeve between the original pipe and backbox. Any recommendations on the pipe? I guess it has to be 45 deg bend pipe to go on between the pipe and backbox? Also, does anybody know the bolt sizes or part number that hold the backbox to the car body via rubber brackets? How to source these out? Any helpful suggestions be much appreciated

Hi Steve yes I did run it in 3rd gear for about 10 15 minutes. I made sure that it’s upto the temperature before I dropped off it at mechanics. But he tested it 4 hours later. when I said it was 0.02 CO, it’s when it’s idle. When it’s tested at 2500rpm, it’s actually 0 thanks scudeny as well for the message.

Good news it passed the MOT CO emission is 0.02% as against 0.2 % limit lambda within the limits as well. Honestly speaking the car feels different as well. Very very quiet and acceleration is noticeably better. just did the terraclean and nothing else. thanks for all the input

yes that’s what I thought to get it done. I will post the retest result on Monday. Fingers crossed.

Thank you

I have someone coming to do a terraclean tomorrow at discounted price (£50). Think will get it done and then go for a 30 min run before going to retest on Monday. But the thing is once I take the car back to garage, there isn’t any guaranty that they will test it then and there. I did ask the garage if they tested it on a warmed up car and they said yes. But I know it may not be right. I will clean the MAF as well before the retest. if needing to replace the o2 sensors, please can you send a link to buy this one. Hope I won’t need it

Please can you direct me in the right direction on how to clean the MAF sensor?

Yes it was last serviced in September 2019 by Lexus, oil and filter service since March 2020, it has only been used about 500 miles and mainly short journeys like 3 4 miles.

Hello never changed it. But if it’s faulty, would it not show up in diagnostic process?

Hello all my 57plate IS250 failed MOT on its emissions. CO emissions 1.62% but the limit is 0.2% lambda emission is 0.95 but limit is 0.97to1.05 The diagnostic was run and there is t any electrical sensor fault and there isn’t any warning light on in the dashboard. The garage has suggested to go for terraclean which will hopefully clear the carbon buildups and result in a lower emission. Could it be the case? Mileage is 99k. any helpful information be appreciated. thank you

Update I got my car back this afternoon. I spoke to the technician and he explained that the code was relating to gearbox shift D solenoid which is all internal. Further he said it was due to second gear not engaged at 7 mph speed. He reckons its a one off thingy and should it happen again, they will have to diagnose it further. He did about ten mile road test in manual mode and codes havent returned back. I dont know which codes were they. I drove back home from dealer and all is looking fine for the time being. I dont notice any problem with gear change. Its smooth as anything. I asked if it could be because of condensation in the gear box and he denied it. He seemed like a decent guy who knew what he is talking about. As per him its very rare that these faults often. All in all i have car back now and enjoyed my ride home. I have to monitor it over next week or so to see if it happens again. I do short journeys during the week. Can it be because of that?

Thanks for all the input guys. The light is still on and i have only driven couple of miles since it appeared yesterday. Its going in tomorrow and will have an update on it. I could read the codes etc myself but prefer for dealer to do it as its under warranty. Plus they will have a lexus code reader than a general one. Will post an update tomorrow wish me luck

Is there a DPF on IS250? I wasnt aware of that. I was under impression that its only in diesels

Hope its just the sensor. It will be covered under warranty - hopefully

Yes, will do that in the evening. I forgot to mention that it has 81k on the clock. I checked the battery terminals, they are all tight.