RoadRash

Adie, long time ago, but I wanted to awake this thread. 🙂 Are you still owning it, or did you really made it to sell this unique car? Let me know some update please. 🙂

Selling my RPS MAX Flywheel & clutch kit for 2JZ engine and Getrag V160 gearbox - 6-paddle unsprung (motorsport) (up to max. 825ftlb = 1,100NM torque) Condition: used approx. 3,000km (mainly wet drifting, hardly any stress or wear - see pictures)) Clutch set incl. swing and screws - €450.- - RPS swing with screwed wear pad - RPS clutch disc (friction lining undamped) - RPS pressure plate - 6 pcs. M8x1.25 screws (mounting clutch on flywheel) - 8 pcs M10x1.25 ARP 12pt swing bolts (HF bolts, not stretch bolts, are reusable!) Optional V160 conversion kit for pull clutch - add +€150.- - Toyota pull fork - Toyota hook with screws - Toyota stocking input shaft with screws - Toyota V160 hydr. Ejection cylinder with screws Location Austria/Europe --> Worldwide Shipping (additional)

SOLD!

4 pcs. Injectors DENSO 250cc (Toyota / Lexus) * out of my IS300 top feed high imp inlet / outlet á 11mm Diameter Middle Diameter 24mm Toyota Part No.: 23250-46090 Price: €60/pcs. (or take 4 pcs. and get package price)

Eagle connecting rods 4340 H-Beam 2JZ (Toyota / Lexus; -GE & -GTE; 6 pieces) Screws: 3/8" ARP 2000 Material: forged 4340 steel Center to Center Length: 5.59" Pin Size: 0.866" Pen End Width: 1.02" Rod End: 2.047" Housing Bore: 2.1667" Big End Width: 1.02" Typical weight: 590 g Bushing for floating gudgeon pin up to approx. 900BHP (linear torque) Ship world wide €350.- (or €400.- shipped worldwide)

Mike's Lexus IS200 IS300 Parts CLICK ME

Sorry, won't be there

HAHA, THANK YOU! *gg* And I'm missing BEO so much since I'm sitting here in Germany. Beograd nedostaje mi puno.... If everything is fine with the Lexus this year I will do a ride down to Belgrade with it. Much time got wasted in the workshop so I need some KMs on it, I'll let you know. :winky:

OK here we go to continue my RaceCar-Project Well, my brakelines look like this right now Got some new valves for higher temparatures, SUPERTECH - 12 EXH. VALVES & 12 INT. VALVES B) Received 6x 870cc injectors from dooderek (Thank You!) Exchanging the radiator frame in the front Fitting the new one in place Spraying some Zinc-Spray and color on the welding places Finish! :) Preparing the engine block for getting a new color After some grinding, sand-blasting and brushing process New black color To be continued..... ;)

would like to do mate, but I have to wait for a whole container of engine parts from the states... .... ... .... JUST FOR ME

Just to let you know how my "RaceCar - Project" is going on... Last weekend we could go on with some small jobs put some body filler into the holes in the engine bay, where could get water and dirt inside Also added some zinc-spray on open metal areas And I decided to turn the engine bay into silver-metalic colour B) And we took care of the brake system, my plan was to remove the ABS block on some other place about 10-15cm toward the front, so we had to cut that ugly brake-line-salad :duh: special care on the order of brakeline-numbers Getting the ABS bracket into the same colour ...fitted on new place installing new connector-fittings pre-fitting the new brake lines bending them into shape Before importing my IS300 from USA to Europe it must have had some terrible accident in the states and got repaired pretty awful in some lazy workshop, so there is still the old radiator-frame inside, that's why my radiator was sitting pretty crooked in place So during this build-up process we will fix that bug also ;) To be continued...

I'll do my best bud, meanwhile it looks like this ...but I'm looking forward to be there, until September shouldn't be impossible. :winky:

If I can fix everything on my IS300 T (meanwhile it's disassembled into pieces ) then I'm playing thoughts to come to JAE 2010. B)

Well, that's the actual condition right now... :P got the block back from honing process Some new goodies.... B) + new throttlebody 80mm ;)

OK, we have removed all devices from the engine (oil pump, water pump, alternator and stuff). In the same run we removed the crank shaft and it looks like that I will need a new one. 0,1mm of material is missing at the Conrod #2 eye at the crankshaft , so they would need to grind and polish, harden and reshaping everything, in the second step I would need thicker bearings for the #2 conrod and I don't know if this is possible. In the end I will need a new crank shaft. ;) The engine builder told me that the cylinder walls look pretty good just slightly honing is required. And he was agreeing that the wasted oil I had inside in the beginning after engine build in 2008 was the main reason for the engine damage. :( The block is already honed, new valves should arrive soon, I will regrind the valve seats and put on the new valves in the cylinder head. Parts for engine rebuild are already ordered and should come here soon...

Well, so we had to grow deeper..... to the source of my problem.... that is some bad news Engine remove There is nothing to say any more :shutit: I think that rod was short before getting glowing crankshaft @ Cyl 2 crankshaft @ Cyl 4 (normal)

OK there is some pause needed to do an engine rebuild.... I was on a drift track, but the fun didn't last very long, after 5-6 turns of fun some strange noise accured outa the engine bay. it was sounding this like :shutit: OK, we had to remove the head from the block and found something strange... We have tested the compression on all 6 cylinders and it had been fine. Removing everything in the front removing valve covers cam shafts removed ARP head bolts removing cylinder head removed and.... in cylinder chamber 3 must be something wrong, it seems to be some fuel problem, maybe due to failed injector or something else, or maybe because of the 10:1 problem i had once (caused by the TPS) watch the edges of the valve seat pockets they're broken or melted away As for the engine noise we noticed..... watch the edges of the piston (up and down side) they seem pretty clean as like touching something (red arrows) Also notice the small cuts in the exhaust valve seat pockets (yellow arrows) we reassembled the cam shafts to check valve train but it seemed to be OK, nothing stucked or anything But watch here cylinder 2 on the head, the piston definately comes in touch with it! NOTE: We have tested this case, so we have turned the crankshaft until piston #2 goes downway (pulling process), we took some rubber hammer and pressed on the piston *klack* it really went down another 1mm :o so it seems to be loosen somewhere in the conrod area. So we have to find out another problem after removing oil pan and take another look... Maybe somebody of you can give some comment what he is thinking about those problems how they can happen or anything!?

And the Euro-LOC had some fun last weekend.... we were having a small meeting on a small race track in Austria for some kind of "race training on wet track" :) a friend of mine chasing me in his MR2 B) Chasing the drifting IS300 Turbo

Having some fun during the Driftsession on Hockenheim Ring in Germany :) After some practice.... ....it got better ;)

Well the stock 5-speed shifter leather sack couldn't be fittet on the C's V160 shifter, so I had to do something before... I have brought the stock leather sack to some saddler to create some new custom shifter sack fitting on the V160 stick black with silver seames B) Well, it really looks like a "Very Short Shifter" but it it OK and very nice to drive Once a time I will have to renew the chrome ball on the top

Differential Installation some words to it: I have brought it to my Lexus Dealer to install the Euro spec IS300 A/T final gearing (1:3,58) in my US spec IS300 M/T (1:3,72) diff housing, including measuring and stuff... It is soooo awsome!! The gears of the V160 feeling now like the 5-speed, simply PERFECT GEARING!! Oil & Servo Cooling System Custom, Custom, Custom...... building clamps.... Connectors for the Servo Cooling Clamps got fitted to the crash bar Finish..... but it was a bloody job, since there is no space to work with :suspiciou in the front: feft side --> Servo Cooler / right side --> Oil Cooler ...and everything is sealed, there is no leaking :)

3" exhaust system (non-cat) This time we had some better tools than for my old exhaust system Remove weld residues step by step we're going backward Once I had some steel catalytic converter.... seems it got shredded... coming to an end The last piece of exhaust has to be created to fit correctly Here we go Installed... :) Videos: :)

Hi mates... just want to let you know what happened to my IS300 Turbo meanwhile... Our Workshop... The Crew.... (they don't even have a driving licence *haha*) :P (those just were some kids hanging around, working on their motocross bikes, helping out a little on race car modifications and stuff) Our Shop has been in perfect situation Down there was a professional machine-shop, they can do everything out of a piece of metal, next to it some supermarket to buy food Another Tools-Market on the other side! Preparing everything for the removing of the W55 and the Torsen Diff First off, to remove the exhaust section W55 & drive shaft removing Same with the Diff Differential Disassembling OS Giken vs. Torsen Well OK, some of my crew members didn't even have the size to get upward the car's height longer wire required Clutch assembling It's a sport's clutch *gg* everything into the tranny We had to widen the upper left hole, to make the bolt fitting It was much easier to lift it up and put it to the engine than the W55 bolting on the clutch Slavecylinder install & covers Adapter brackets for the tranny cross member Placing the differential 1-piece driveshaft fits That's what I call a ShortShifter ALL IN ALL.... B)

As one of the first few guys in the world who has done a turbo conversion on the IS200, I can wish you good luck blowing 1.2bar of boost on the stock engine which is running 10:1 compression ratio, especially when using pump gas. But when reading your posts I'm wondering if everybody else as like TDI, Prolex and others has done big mistakes to the setups on their IS200T projects since they couldn't hold 0,9bar of boost, didn't they? Several people have tried to go for higher boost on stock internals and they all have destroyed their engines.... so I'm wondering, why there is just one out there which can make it?!? ;) Sorry for being pessimistic, but this sounds for me like "Yes we know that cars are built for driving, but OURs CAN FLY!"