Do Not Sell My Personal Information Jump to content


  • Join The Club

    Join the Lexus Owners Club and be part of the Community. It's FREE!

     

Leak into the boot


RevPhilip
 Share

Recommended Posts

Hi All,

I am looking for wisdom and advice please...

I have had tell tale signs of a leak in the boot, water of the cover that sits under the roof when the roof is in the boot (Please see photos) 

The boot liner is wet right above where the third break light sits and I have read that this is a problem area for roof leaks, and you need to take off the boot cover, take off the brake light and re-seal and put everything back together. 

So how do I get the clips off? (Please see photo) Do I just try and pull them off? Then what do I seal the brake light with and where do I seal it? All around the edge, or just at the back?  

Thank you in  advance for any help or ideas.

Philip 

 

 

IMG_7732.jpeg

IMG_7733.jpeg

IMG_7734.jpeg

IMG_7731.jpeg

Link to comment
Share on other sites

If it's a small leak, and you want to have a go at fixing it without the faff off taking things apart, then you might want to try something called Captain Tolleys Creeping Crack Cure. It's a thin, milky coloured liquid, often used to seal hard to find leaks in hatches etc on boats. I've used it with some success on leaks in a windscreen and trim surrounds.

Basically you pour it along any joins and it seeps into any gaps and seals the leaks. It may or may not be sufficient for your leak, but is cheap and easy to try. If not then it's a case of taking thinks apart and  silicone sealant.

  • Like 1
Link to comment
Share on other sites

I have a water ingress in exactly the same place. I have improved on what it was but its not 100% yet.

The back corner of the boot aperture seal has a drain hole in it, make sure it's clear or water pools there and comes over the seal.

There is plastic cup at the back corners, these have a hole and a rubber drain hose, make sure that is clear.

Give all the seals with a good coating of Shin Etsu grease which will rejuvenate them.

Screenshot_20221015-073508_eBay.thumb.jpg.495c918f4cac82a65edb3d68be0fcb7c.jpg

 

Next cross your fingers and retest!!

Good luck, Anthony 

 

Link to comment
Share on other sites

On 11/17/2022 at 10:26 PM, Lexiguy said:

I have a water ingress in exactly the same place. I have improved on what it was but its not 100% yet.

The back corner of the boot aperture seal has a drain hole in it, make sure it's clear or water pools there and comes over the seal.

There is plastic cup at the back corners, these have a hole and a rubber drain hose, make sure that is clear.

Give all the seals with a good coating of Shin Etsu grease which will rejuvenate them.

Screenshot_20221015-073508_eBay.thumb.jpg.495c918f4cac82a65edb3d68be0fcb7c.jpg

 

Next cross your fingers and retest!!

Good luck, Anthony 

 

I have followed this recurring issue here and on the other (mainly US members) forum.  Luckily, I don’t have the leak problem (yet) and so I am not totally au fait as to where all the drain holes are to check and clear where necessary.  May I suggest it a good topic to consider for a potential workshop subject at our next summer meet?

  • Like 2
Link to comment
Share on other sites


Having read and re-read as many posts I could both from here and from America, I plucked up the courage to have a go at fixing the leak. I have attached some photos of what I did. I did clean up the silicon before putting all the tape on, the tape was only on there to allow the silicon to dry. I have checked it once since and it’s 95% better 😎 maybe I should have another check tonight? 
 

I also took some trim off to see if I could find any other source to the leak. 

8B404627-9A52-4D71-B6AC-EA4FBFE02033.jpeg

A0A434E3-9BA5-4D11-B047-885C725AD0E6.jpeg

0B4E5F13-161C-458C-B317-FE0120C0683A.jpeg

5C3E6EA4-E4A2-4A63-A4C0-5E7F451C724D.jpeg

  • Like 1
Link to comment
Share on other sites

On 11/17/2022 at 5:58 PM, Russ59 said:

Bob will have the answer on this aswell as anything else on the SC.

He is a hive of useful info, he should write a manual on all the pitfalls and repairs.

C’mon Bob😂😂

Only any help if I’ve done the job in question ☹️

high level brake light reseal would be first suggestion.

then runs some kids coloured chalk around the rubber boot seal ,then next time it rains see if any chalks has been washed away ….that will be the leak area 👍🏻

  • Like 3
Link to comment
Share on other sites

Latest Deals

Lexus Official Store for genuine Lexus parts & accessories

Disclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via eBay links

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share







Lexus Owners Club Powered by Invision Community


eBay Disclosure: As the club is an eBay Partner, the club may earn commision if you make a purchase via the clubs eBay links.

DISCLAIMER: Lexusownersclub.co.uk is an independent Lexus forum for owners of Lexus vehicles. The club is not part of Lexus UK nor affiliated with or endorsed by Lexus UK in any way. The material contained in the forums is submitted by the general public and is NOT endorsed by Lexus Owners Club, ACI LTD, Lexus UK or Toyota Motor Corporation. The official Lexus website can be found at http://www.lexus.co.uk
×
  • Create New...