Do Not Sell My Personal Information Jump to content


  • Join The Club

    Join the Lexus Owners Club and be part of the Community. It's FREE!

     

1998 Ls Key Programming To Start The Car


Recommended Posts

I have 1998 LS400 and I bought a new key from eBay.

Now when I tried to program the key to the car, wireless part was no problem but actually to be able to start the car with the new key, no luck.

I followed instructions from service manual but still nothing.

When I enter to to the programming mode, the security light blinks once and after that nothing. Even I wait for 2-3 minutes, the key does not get programmed but also the security light does not blink more than once. If I stop the programming sequence, then when entering the new key to the ignition, security light blinks and if I enter the master key, security light stops blinking.

But what is so strange here is that the new keys opens the doors without any errors.

Does anyone know why in programming mode the light only blinks once, since it is supposed to be doing blinking all the time untill key is programmed.

Link to comment
Share on other sites

If you have bought a complete (strange) key, the ECU will have to be programmed to accept the chip in the new key to disengage the immobiliser. Which is a different procedure.

I could be wrong, if so, someone else will come to tell me off :)

Link to comment
Share on other sites

Hi



Fieat of all make sure you get the correct key - it should be a denso 12569 and the lock button should have a dot on it and the unlock button should have a triangle on it



The method i used is posted here by haylands here and it worked fine:



http://www.lexusownersclub.co.uk/forum/topic/47560-ls400-key-programme/

Link to comment
Share on other sites

My master key has dot in lock button, but no triangle in unlock button, same with the new key.

Both are 3 button keys. I think I will change the Battery to master key and try again. I have tried both method 1 & 2 from the link cruisemark posted.

I think this is the method to program the key to the ecu.

Link to comment
Share on other sites

I went through this earlier in the year and struggled at first, but managed it after about 10 attempts. I did make sure the spare key was identical to the master, i.e. with the triangle and the dot. In the end I wrote out the instructions so they were easier for me to understand. If you pm me your email address I'll send it to you as it may help.

  • Like 1
Link to comment
Share on other sites

Ok, so I went to the local locksmith and they said that the keys do not match with the master key and secondary key.

They were able to order me a new key, it will not have a remote function but it should start the car.

So then I can use the another key to open the doors and another to start the car, good enouh to me :)

And will also have existing master key as a back up.

Link to comment
Share on other sites


I thought the key that goes into the ignition had to be programed or the immobiliser will prevent it starting, When I had mine cut, it would turn the engine over, but wouldn't start until it was programed.

Link to comment
Share on other sites

There are actually two different items in the key integrated under a plastic cover (chip). First one gives the signal to the car to open and close the doors, but second one gives the signal to the immobiliser to actually start the car. And now the second chip does not match with the master key. Therefore I can program the key to open the doors but I cannot program the another chip to start the car.

Link to comment
Share on other sites

Ok, so I went to the local locksmith and they said that the keys do not match with the master key and secondary key.

They were able to order me a new key, it will not have a remote function but it should start the car.

So then I can use the another key to open the doors and another to start the car, good enouh to me :)

And will also have existing master key as a back up.

that doesnt sound right - the remote key has the gizmos stored in it - and when inserted will start the engine - if the new key is plain non remote key how will it start the engine?

Link to comment
Share on other sites

Great news,

the local locksmith was able to create a new key to my car and even better is that it works.

It does start the car and I can open and lock the door manually without triggering the alarm.

So now I can use the key from eBay as wireless function and the new key to start the car and master key I can leave as spare key.

  • Like 1
Link to comment
Share on other sites

Latest Deals

Lexus Official Store for genuine Lexus parts & accessories

Disclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via eBay links

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share






Lexus Owners Club Powered by Invision Community


eBay Disclosure: As the club is an eBay Partner, the club may earn commision if you make a purchase via the clubs eBay links.

DISCLAIMER: Lexusownersclub.co.uk is an independent Lexus forum for owners of Lexus vehicles. The club is not part of Lexus UK nor affiliated with or endorsed by Lexus UK in any way. The material contained in the forums is submitted by the general public and is NOT endorsed by Lexus Owners Club, ACI LTD, Lexus UK or Toyota Motor Corporation. The official Lexus website can be found at http://www.lexus.co.uk
×
  • Create New...