Mr Singh

Happy Birthday mate :)

looks good :)

Your sticker End of the day its upto you, i'm only observing :)

The rear caliper sticker is on wrong?! Fuel Pressure Reg. Mounted ontop of the ECU gubbins. Thats not where i would mount it :o Surely you have to undo the hoses to get enough slack to open the cover? which when next to electrical cables... fuel.. spark. BANG! I would not be comfortable with that mounting arrangement.

Toyota Altezza, S11NCN, Am. :)

I might come to this one.

Dont know if anyone else watched it, but this tickled me. You cant beat a good bit of toilet humour to raise a giggle http://vids.myspace.com/index.cfm?fuseacti...eoid=1272720922

Looks good :)

They are useful...to signal to other brain dead tw@ts on the road..."Look at me...its not foggy,see...I have foglights and sidelights on...my car is a higher spec than yours and looks lower". I have no pity for police man pulling people over... for incorrect use. Hell they should take a sledghammer to them.. I have never in 3yrs of owning my car had to use them...

Ditto that. Maybe he will get bored and come back to F1... unlikely but there you go.

I have +37mm offset fronts... on 8x19s with 225s.. And i have major tuckin too ;)

Happy Barr-day and Diwali :D

Its cheaper just to get a pallet service, we use them for around £50+ VAT for upto 500kilos I also have a same day courier who does runs for around £60 a day, he will collect then deliver. Look in the yellow pages :)

Altezza?

http://www.postvan.com/uk/ Try these guys :)

Is that your old setup?

Shame you didn't have a go at making the arm rest then :o A you said you wanted so you payed the price. What the hell as that got to do with a Gauge pod :duh: Thats a totally different kettle of fish, metal bracket, hinge mech, plastic tooling, leather, sponge. :duh:

Anyone can give it a go, its like paper mashay :D I didn't say pay someone to make it, i said you can DIY for peanuts. I'd happily make it, given time for someone, wouldn't take more than 3-4hrs. Or make a moulding and produce them in bulk :) Besides, how much would the prolex one cost, if you time to take to painter etc......... closer to £280ish right?

It was for Focals Demo car at CES 2003. Done by Cartunes in CA (USA) I met the owner of that car and the installer when i was in las vegas few yrs back... got some pics somewhere. Bet it cost more than £40 ........... 1kg Roll CSM 300gm (3.3 square metres) = £3.86 5kg pack Low Cost Resin with catalyst (5ltrs) = £12 Easy Sand Body Filler 500gm pack = £3.86 Paint brush for resin = £1 Old t-shirt = £0 6mm MDF for rings = £1 from timber yard dowels = £1 from timber yard masking tape = £2 (50mm best) Primer = £3 Satin black paint = £3 £30.72+ VAT £36.09 To paint it like Tysen did on there focal demo car, i'd give £20 to a body shop to do that for me :) (so take out the £7 for paint above and that makes it £50 or therebouts?

It was for Focals Demo car at CES 2003. Done by Cartunes in CA (USA) I met the owner of that car and the installer when i was in las vegas few yrs back... got some pics somewhere.

Granted, he's lost the air vents, but that was to make space for center channel, since its a Focal Demo car, but thats the basic idea. :) It is not like plastic that you would think, plastic :duh: if you know what i mean, it feels more like a sort of pot, its very well made :) not like plastic at all. :o What difference is it, made from plastic or fibreglass? Agreed, if it was an exterior mod i would look for plastic/PU where possible. But for £250, its just a rip off :)

Whatever you wanted mate! 1st, make a base using 2 layers of fibreglass matting Then make some rings depending on the size of the gauges hot glue them in place using wooden dowels use some fleece or an old t-shirt, stretch it over, around and under. soak in resin, allow to harden. sand and trim off access. use some fine filler like rage green fine icing filler, sand. primer then paint, or trim in alcantara or layer with carbon fibre weave. I could knock one up in couple of hours, and would cost no more than £40 for materials. £250, yeh for convenience, but really for a moulding that is just injection moulded... thats plain ridiculous IMO :) I'd like to see that myself :duh: You haven't seen my fibreglass skills. Wanna bet i can't make one ;)

Absolutley lush B) Wheels look little lost though, could do with some heft spacers

You can make that pod holder for less than £40 tops, another £40ish you can layer it in real carbon fibre. Granted, it won't be plastic (fibreglass) but who in the hell cares?

Greddy Turbo, 19s and a supercross front bumper... Any idea on price?